Baba Automobile Pvt. Ltd. - An ISO 9001:2015 Certified co. Contact - 8769405920, 8387070109, Head Office Jaipur & Our Training Center - Jaipur, Bhopal, Pune, Noida, Bengaluru, Mumbai & Udaipur.
Outboard motors – BABA AUTOMOBILE
Nuclear power plants
June 20, 2016
June 20, 2016

Outboard motors

Outboard motors

Until engines were invented, the only way to power a small boat was with oars or sails. Calm and elegant it might have been, but it took ages to get anywhere quickly—and you had to rely on there being wind or muscle power available. Outboard motors have changed all that. Invented in the early years of the 20th century, outboards brought the same freedom to small boats that gasoline engines brought to cars. Let’s take a closer look at these handy machines and find out how they work!

Using an outboard

If you’ve read our article on car engines, you’ll know that they produce motion by burning gasoline with oxygen in metal cylinders. The cylinders have sliding pistons that push a crank around and the crank drives a shaft that (eventually) powers the wheels. Much the same happens in an outboard motor. The main difference is that there are usually fewer cylinders, operating in either a two-stage or four-stage cycle. Instead of driving a gearbox, the motor powers a propeller. To steer a boat with an outboard motor, you simply tilt the whole motor casing so the propeller pushes the water away from it at an angle. (Some outboards you can tilt by hand; others are steered by turning a steering wheel that tilts the motor using hydraulic cables.) You can go faster by opening up the throttle so the outboard burns more fuel and turns over more quickly.





How does an outboard motor work?

In theory

Open up an outboard and this—hugely simplified—is what you’ll find inside:

  1. Fuel burns in the cylinder (or cylinders) to make power. There’s a fuel tank (not shown) inside the case of the motor at the top, big enough to hold perhaps 23 liters (6 gallons) of gas. The heavier your boat, the faster you drive it, the choppier the water, the more heavily loaded, or the lower in the water it sits, the more fuel you’ll burn.
  2. Powered by the burning and expanding fuel gases, a piston moves back and forth in the cylinder. This is just like the piston in a car-engine cylinder and often works through the same four-step process (four-stroke cycle), although some outboards do use a simpler two-stroke cycle.
  3. The piston rod turns the crankshaft, converting the back-and-forth (reciprocating) motion of the piston into round-and-round (rotary) motion.
  4. The crankshaft turns the main driveshaft running down the long spine of the motor.
  5. A small gearbox at the bottom of the driveshaft converts vertical spinning motion into horizontal spinning motion.
  6. The propeller powered by horizontally spinning gears powers the boat through the water.


In practice

The very simplified illustration up above is designed to show you the basic operating principle of an outboard motor; real motors are somewhat more complex than this! Here’s a very clear cutaway illustration prepared by Suzuki Motor Corporation for a patent application they were granted in 1999 for a new design (US Patent #5,980,341: Outboard Motor). I’ve colored it and greatly simplified the numbering so you can make sense of it more easily; if you want to know all the details, check out the patent, where you’ll find more drawings of the same engine. Here a few of the parts that are worth noting:

  1. Flywheel (blue): A heavy wheel that builds up momentum as the engine accelerates, helping to maintain a smooth and steady engine speed.
  2. Starter motor (grey): Normally you’d start an outboard motor electrically, just as you’d start a car. If that’s not possible, you can attach a pull cord to the flywheel and tug it vigorously to “crank” the motor into life. There’s a special notch in the flywheel where you attach the cord. (Find out more about flywheels.)
  3. Crankshaft (red): Collects power from the engine pistons, which fire slightly out of step to keep the motor running at a steady speed
  4. Cylinders (blue): This motor has three cylinders arranged horizontally. A medium-sized, three-cylinder outboard like this produces something like 40–50 horsepower. It’s a fairly hefty machine, weighing in at 86kg (190lb)—almost the exact average weight of an American adult male!
  5. Pistons (yellow): Move back and forth in the cylinders, driven by the energy released from burning fuel, and transferring that energy to the crankshaft.
  6. Carburetors (orange): Three separate carburetors combine fuel with air to make an explosive mixture—there’s one for each cylinder.
  7. Camshaft (green): Opens and closes cylinder valves that let fuel in and exhaust gas out.
  8. Fuel pump: Sends fuel to the carburetors.
  9. Sparking plugs (red): ignite the fuel in the cylinders.
  10. Mounting bracket: Where the motor attaches to the back of the boat and swivels up and down.
  11. Driveshaft: Carries power from the crankshaft down to the gears. Think of it as a kind of “spinning spine,” running straight down through the center of the motor linking the cylinders at the top to the gears and propeller at the bottom.
  12. Anti-ventilation/cavitation plate: Cavitation is what happens when a spinning propeller churns up air or engine exhaust gas in the water. Bubbles form and burst, which, over time, wear away the propeller’s surface. The anti-cavitation plate is designed to reduce that problem, but cavitation can still be caused by floating debris disrupting the smooth flow of water around the propeller blades.
  13. Gear unit: The gears (not shown) are inside here.
  14. Propeller.

Comments are closed.

Online Training